#include <modm/driver/pressure/bme280.hpp>
|
|
using | Calibration = modm::bme280data::Calibration |
| |
|
using | Data = modm::bme280data::Data |
| |
|
using | DataBase = modm::bme280data::DataBase |
| |
|
using | DataDouble = modm::bme280data::DataDouble |
| |
|
typedef Configuration< CtrlMeas_t, Mode,(Bit1|Bit0) > | Mode_t |
| |
|
typedef Configuration< CtrlMeas_t, Oversampling,(Bit2|Bit1|Bit0), 2 > | Pressure |
| |
|
typedef Configuration< CtrlMeas_t, Oversampling,(Bit2|Bit1|Bit0), 5 > | Temperature |
| |
|
typedef Configuration< CtrlHum_t, Oversampling,(Bit2|Bit1|Bit0), 0 > | Humidity |
| |
|
typedef Configuration< Config_t, TimeStandby,(Bit7|Bit6|Bit5) > | TimeStandby_t |
| |
|
| enum | CtrlHum : uint8_t |
| |
| enum | Status : uint8_t |
| |
| enum | CtrlMeas : uint8_t |
| |
| enum | Mode : uint8_t |
| |
| enum | Oversampling : uint8_t |
| |
| enum | Config : uint8_t |
| |
| enum | TimeStandby : uint8_t |
| |
| enum | FilterSettings : uint8_t |
| |
|
|
| MODM_FLAGS8 (CtrlHum) |
| |
|
| MODM_FLAGS8 (Status) |
| |
|
| MODM_FLAGS8 (CtrlMeas) |
| |
|
| MODM_FLAGS8 (Config) |
| |
| | Bme280 (Data &data, uint8_t address=0x76) |
| |
|
modm::ResumableResult< bool > | initialize (Mode mode=Mode::Normal, Oversampling temperature=Oversampling::Single, Oversampling pressure=Oversampling::Single, Oversampling humidity=Oversampling::Single) |
| | Reads out and stores the calibration bytes.
|
| |
|
modm::ResumableResult< bool > | readout () |
| | Read the raw data from the sensor. Conversion must be freerunning.
|
| |
| modm::ResumableResult< bool > | startMeasurement (Oversampling temperature=Oversampling::Single, Oversampling pressure=Oversampling::Single) |
| |
|
Data & | getData () |
| | Get the data object for this sensor.
|
| |
template<typename I2cMaster>
class modm::Bme280< I2cMaster >
- Author
- Sascha Schade
- Template Parameters
-
template<typename I2cMaster >
| modm::Bme280< I2cMaster >::Bme280 |
( |
Data & |
data, |
|
|
uint8_t |
address = 0x76 |
|
) |
| |
- Parameters
-
| data | pointer to buffer of the internal data of type Data |
| address | address defaults to 0x76 |
template<typename I2cMaster >
| modm::ResumableResult<bool> modm::Bme280< I2cMaster >::startMeasurement |
( |
Oversampling |
temperature = Oversampling::Single, |
|
|
Oversampling |
pressure = Oversampling::Single |
|
) |
| |
Start a single measurement in forced mode. Sensor will go to standby after this. To reduce bus traffic only the absolute necessary register (CTRL_MEAS) is written. If oversampling of humidity shall be changed, another method must be used.
The documentation for this class was generated from the following file:
1.4.2 
